Wood Floor Refinishing Omaha

Wood Floor Refinishing Omaha. Last spring I took two weeks off from work to relax and unwind and just do nothing. But on the very third day of my holidays, I was completely bored with my new routine. So, I started looking for ways on how to effectively use this time. That is when it occurred to me that the wooden flooring in my living room was screaming for my attention for quite some time now. The finishing had been completely worn off in most places, and still some areas looked worse than the rest due to high trafficking in those parts. There were a few squeaky floor boards, exposed nail heads, some major stains from spills, not to mention too many scratches on the floor. After having found myself a project to keep me busy over the next few days, I started looking for exclusive guidelines on Manhattan wood floor refinishing in and around Manhattan.

My very first step was to finish all the repair work before I started the actual refinishing process. I knew that floor sanding would take care of the traffic patterns on the floor along with most of the stains from spills. So, I focused my energies on taking care of the loose floor boards, knocking down raised nail heads. This process left some holes in the floor which later I would fill with filler made from mixing sawdust and some glue. After finishing the repair work, and giving the floor a thorough cleaning, I was ready to move on to sanding the floor.

For sanding, I rented a sander from the nearest hardware store, which was a wise choice for me as after finishing my own living room; I had no intention of pursuing this as a fulltime profession. The big sander took care of most of the living room floor, but for edges and corners I used a random orbit sander. Once I was done with sanding the floor, I filled the holes with some filler, and after it was dry, did some more sanding. To my delight all signs of stains and minor scratching were gone, and not much was left for me to do but to get on with the refinishing. Before applying finish, I had to vacuum the whole area again and also clean with a damp cloth so as to get rid of all sawdust. After having applied three coats of oil based finish, my living room floor looked as good as new.

Following these simple guidelines for Manhattan wood floor refinishing I was able to transform my flooring from dull and worn looking to its gleaming and pristine condition. The remainder of my holidays I spent admiring my own handiwork whenever I looked at the glossy surface of my living room floor.

Wood flooring refinishing breathes new life into old, dull hardwood floors. Often, older homes have gorgeous hardwood floors waiting to be discovered underneath old, tattered carpet. If you discover this hidden gem in your home, consider giving those floors a new life with the right fix.

The first step in brightening up your floors is determining whether or not the boards are good candidates for the process. If you find that the boards are warped, buckled, soft, soggy, or saggy, they need to be replaced. If they are dull and scratched, but otherwise solid, then it is time to look into wood flooring refinishing.

The hardest part about the process is sanding the floors. Use a drum sander with 20 to 36 grit sandpaper to buff up the floor. Start slowly, as the machine can scuff your floors. After you place the sander in place, walk forward along the grain of the hardwood, from one half of the wall to the other, making two passes over each row. Do not allow the sander to sit for even a second or two in one spot. Always keep moving. Then, use an edge sander to finish the job. Repeat the process with a medium grit sandpaper and a fine grit sandpaper.

When you are done sanding, you will find dust all over the room. The next step in wood flooring refinishing is cleaning up all of that dust. Leaving any of it on the floor when you stain it will cause problems. Use a shop vac to thoroughly clean the room.

The next step is staining the floor. Follow the directions on the stain, and be sure to ventilate the room. Always follow behind yourself with a clean rag to wipe up any excess stain. Leave the stain to dry overnight before sealing it or walking on the floor.

Once the floor is clean and stained, apply sealant. Use around three coats, and allow three hours for it to dry before adding another coat. If you choose a water-based urethane as your finish, you will need more than three coats. Be careful about stirring up dust while the finish cures on the floor. Leave it for approximately three days before putting your furniture back.

Wood flooring refinishing is a huge time commitment as a do-it-yourself project. Homeowners who do not have excessive amounts of time to spend on home improvement projects can hire a professional to do the task. Professionals are trained on using the sander and quickly applying the stain and sealant. For those with busy schedules, hiring someone to do their wood flooring refinishing is a cost-effective option.

Article Source: http://EzineArticles.com/5232172

Leave a Reply

Your email address will not be published. Required fields are marked *